Unbranded 2008 - 2014 WRX STI 52mm center vent dual gauge pod mount
Unbranded 2008 - 2014 WRX STI 52mm center vent dual gauge pod mount
Unbranded 2008 - 2014 WRX STI 52mm center vent dual gauge pod mount
Hey! Up for sale I have these custom wrx/sti gauge mounts for the
2008-2014 generation. These allow you to install an aftermarket 52mm
gauge into your interior without disrupting the oem design. As a bonus
there are vents around the gauge hole that allow your vents to still
function like normal. Please read below for more details!
----->Fitment
These are designed to fit the original panels on 2008-2014 wrx/sti. They are very easy to install, and simply click into place using the mounting points of the original ac vent. They are designed to hold a 52mm gauge. Some gauges may have a trim ring that goes around the gauge. If that ring is too big, it may not clear the original panel, so you would need to space the gauge further out. Ive not encountered this issue before, but i know every brand is different. Any gauge that has a trim over 62mm may run into that issue. Please read the instructions below for more details.
----->Materials
Unlike others who use cheap 3d prints that have a terrible finish and warp easily, these are made from 1/4in lasercut high gloss black acrylic. They are much stronger and dont look cheap comparatively. I may offer other materials, please read the custom section below.
----->Important!
-THIS LISTING IS ONLY FOR A VENT PANEL TO HOLD THE GAUGE. THERE ARE NO GAUGES INCLUDED, AND NO OEM DASH PANEL INCLUDED.
-Triple panels require you to cut the center piece on your original vent trim
-Since
each gauge is different I do not include mounting provisions. That is
always included with your gauges when purchased. The holes on these are
not designed for a friction fit. I usually use the "u" clamps included
with the gauge, or the rubber band style. If you are missing those, you
can use a ziptie wrapped around the gauge to pin it to the panel. -While strong, these are still made from acrylic and can crack/snap if handled improperly. Please do no drop or bend.
-Do not use harsh cleaners or you may damage the finish.
-These only install one way, so please read the instructions below for details.
-The original vent is held on by small clips and these vent mounts reuse the same ones. You must handle these clips carefully as they can snap. Please read the instructions below and understand that im not responsible for any damage you incur. If you do break a few clips it should still hold as there are 8 all together. A dab of silicone or glue can substitute a broken clip if necessary.
----->Custom Options
-While this listing is for dual gauge, I do have single/triple guage listed as well. Check my other listings in my profile or send me a dm.
-These are made in house and can be tailored to your needs in any way you can think of. I can do different positioning for the gauges, different shapes if you have a different item youd like to mount, like a boost controller for example. Blockoff plates, switch mounts, etc. If you have an idea, feel free to reach out.
-Currently there arent too many color options in 1/4in acrylic. If you are willing to take a risk with running 1/8th acrylic, i can offer a few more colors and finishes. They can be painted and vinyl wrapped as well.
-Additional logos/writing can be etched onto the panels if youd like.
----->Instructions
Please look at the assembly pic in the listing, and read below. Message me if you cant figure it out based on these instructions. Wearing gloves is recommended to prevent finger prints, and a soft microfiber towel is recommended if you need to wipe the panels clean. Do not use aggressive chemicals on acrylic.
1) Remove your original panel, it can be pryed off the dashboard. I usually start at the top and work my way down. A trim pry tool is highly recommended to prevent damage. (Not pictured)
2)
Once removed, place the panel face down and locate the 8 tabs that hold
your factory vents to the panel. Beginning on the bottom side,
carefully pry the 4 tabs open while pulling the vent away. Be careful,
because you can snap these. Once the bottom is free, the vent can be
pulled off the panel.
3)
Take your new gauge panel, and notice that "front" is etched on one
side. That side faces outward. To install, you need to angle the panel
into the top tabs first. Once the teeth are lined up, push them into the
top holes, and then there will be enough space to angle the bottom side
down and push it into the bottom clips. So top clips first, then
bottom, it wont work if you try it any other way, and you may break the
panel.4)Install your gauges, and reassemble into the interior.
**To remove, unclip the panel from the bottom 4 teeth first, and then slide and angle them out of the top teeth.
| Brand: | Unbranded |
|---|---|
| Isin: | IVC5351ICPXD |
Out of Stock
In Stock
Backordered
Out of Stock
IBspot Buyer Protection
Shop confidently on IBspot, receive your item as described or your money back for eligible orders. Learn Program Terms
GUARANTEED SAFE CHECKOUT
-
MONEY BACK GUARANTEE
30 days money back guarantee, no additional fee charged.
-
EXCELLENT SUPPORT
We provide 24/7 online customer support via email.
-
Fast Shipping
One week domestic shipping. Global delivery to the US in 2 weeks.
Hey! Up for sale I have these custom wrx/sti gauge mounts for the
2008-2014 generation. These allow you to install an aftermarket 52mm
gauge into your interior without disrupting the oem design. As a bonus
there are vents around the gauge hole that allow your vents to still
function like normal. Please read below for more details!
----->Fitment
These are designed to fit the original panels on 2008-2014 wrx/sti. They are very easy to install, and simply click into place using the mounting points of the original ac vent. They are designed to hold a 52mm gauge. Some gauges may have a trim ring that goes around the gauge. If that ring is too big, it may not clear the original panel, so you would need to space the gauge further out. Ive not encountered this issue before, but i know every brand is different. Any gauge that has a trim over 62mm may run into that issue. Please read the instructions below for more details.
----->Materials
Unlike others who use cheap 3d prints that have a terrible finish and warp easily, these are made from 1/4in lasercut high gloss black acrylic. They are much stronger and dont look cheap comparatively. I may offer other materials, please read the custom section below.
----->Important!
-THIS LISTING IS ONLY FOR A VENT PANEL TO HOLD THE GAUGE. THERE ARE NO GAUGES INCLUDED, AND NO OEM DASH PANEL INCLUDED.
-Triple panels require you to cut the center piece on your original vent trim
-Since
each gauge is different I do not include mounting provisions. That is
always included with your gauges when purchased. The holes on these are
not designed for a friction fit. I usually use the "u" clamps included
with the gauge, or the rubber band style. If you are missing those, you
can use a ziptie wrapped around the gauge to pin it to the panel. -While strong, these are still made from acrylic and can crack/snap if handled improperly. Please do no drop or bend.
-Do not use harsh cleaners or you may damage the finish.
-These only install one way, so please read the instructions below for details.
-The original vent is held on by small clips and these vent mounts reuse the same ones. You must handle these clips carefully as they can snap. Please read the instructions below and understand that im not responsible for any damage you incur. If you do break a few clips it should still hold as there are 8 all together. A dab of silicone or glue can substitute a broken clip if necessary.
----->Custom Options
-While this listing is for dual gauge, I do have single/triple guage listed as well. Check my other listings in my profile or send me a dm.
-These are made in house and can be tailored to your needs in any way you can think of. I can do different positioning for the gauges, different shapes if you have a different item youd like to mount, like a boost controller for example. Blockoff plates, switch mounts, etc. If you have an idea, feel free to reach out.
-Currently there arent too many color options in 1/4in acrylic. If you are willing to take a risk with running 1/8th acrylic, i can offer a few more colors and finishes. They can be painted and vinyl wrapped as well.
-Additional logos/writing can be etched onto the panels if youd like.
----->Instructions
Please look at the assembly pic in the listing, and read below. Message me if you cant figure it out based on these instructions. Wearing gloves is recommended to prevent finger prints, and a soft microfiber towel is recommended if you need to wipe the panels clean. Do not use aggressive chemicals on acrylic.
1) Remove your original panel, it can be pryed off the dashboard. I usually start at the top and work my way down. A trim pry tool is highly recommended to prevent damage. (Not pictured)
2)
Once removed, place the panel face down and locate the 8 tabs that hold
your factory vents to the panel. Beginning on the bottom side,
carefully pry the 4 tabs open while pulling the vent away. Be careful,
because you can snap these. Once the bottom is free, the vent can be
pulled off the panel.
3)
Take your new gauge panel, and notice that "front" is etched on one
side. That side faces outward. To install, you need to angle the panel
into the top tabs first. Once the teeth are lined up, push them into the
top holes, and then there will be enough space to angle the bottom side
down and push it into the bottom clips. So top clips first, then
bottom, it wont work if you try it any other way, and you may break the
panel.4)Install your gauges, and reassemble into the interior.
**To remove, unclip the panel from the bottom 4 teeth first, and then slide and angle them out of the top teeth.
- Modified Item: No
- Country/Region of Manufacture: United States
- Custom Bundle: No
- Surface Finish: Lasercut Gloss Black Acrylic
- Manufacturer Part Number: Does Not Apply
- Brand: Unbranded
- Fitment Type: Direct Replacement
- Non-Domestic Product: No
- Warranty: No Warranty
- UPC: Does not apply
Processing Time
- We process and ship orders Monday through Friday, excluding holidays.
- Most orders are processed within 1–3 business days, depending on product availability.
- Processing time does not include delivery time, which varies based on your location and the product’s shipping origin.
Shipping Coverage
We currently ship to addresses within the United States only.
Products may ship from:
- Our U.S. warehouses, or
- Our international fulfillment centers (including Korea, Japan, China, Australia, Mexico, Canada, the United Kingdom, and the EU).
Each product page clearly displays the “Ships From” location before checkout.
Shipping Methods & Estimated Delivery
| Shipping Method | Estimated Delivery | Cost |
|---|---|---|
| Free Shipping (US) | 5–10 business days | Free, available on eligible items |
| Standard Shipping (US to US by Item) | 5–10 business days | $6.50 for the first item, $2.00 each additional |
| Standard Shipping (From US Warehouse by Weight) | 3–7 business days | Starts at $6.50, increasing by $2 for every additional 4 oz (0.25 lb) up to 1 lb, then by $4 for each additional pound beyond 1 lb. |
| Extended Delivery (Ships from Overseas Warehouse) | 10–20 business days | $14.50 for the first item, $2.00 each additional |
Shipping costs vary by product weight, quantity and origin. Exact rates and delivery estimates are displayed on each product page and confirmed during checkout.
Free Shipping
We offer free standard shipping on select products or during promotional periods. Availability of free shipping will be displayed on the product page and at checkout.
Carriers
We primarily use USPS and UPS for U.S. deliveries. Items shipped from international warehouses may be handled by partner carriers depending on the country of origin.
Import Duties & Taxes
All import duties and taxes for goods imported into the United States are included in the product price. There are no hidden fees or additional charges at checkout.
Tracking & Notifications
Every order is fully trackable. You will receive a tracking number via email once your order ships. If your order ships in multiple packages, each package will have its own tracking number. If you don’t receive a shipping confirmation immediately, your order is still being processed and will arrive within the estimated timeframe shown at checkout.
You can track your shipment anytime using the Track Your Order page on our website.
Order Changes & Cancellations
If you need to modify or cancel an order, please contact our customer support team as soon as possible. Orders can only be canceled before they ship. Once shipped, cancellations are not possible, but you may request a return after the item is delivered.
Contact: support@ibspot.com
Item Not Received
If your tracking number shows “Delivered” but you haven’t received your package:
- Check with your local USPS or UPS office.
- Confirm that the shipping address provided was correct.
- If the issue remains unresolved, contact support@ibspot.com for assistance.
Damaged or Lost Parcels
If your package arrives damaged or fails to arrive, please contact us immediately. For deliveries to P.O. boxes, ibspot is not responsible for damage caused by weather, temperature, or theft.
Customer Support
For any questions about shipping, tracking, or delivery, our customer support team is here to help.
Email: support@ibspot.com
We’re always happy to help.
Please read our policy carefully before making a purchase.
We aim to ensure every customer has a smooth and transparent experience with ibspot.com.
Order Cancellation Policy
Customers may request to cancel an order before it has been shipped.
Once the package has been shipped, cancellations are no longer possible; however, you may still request a return after receiving your order.
How to Request a Cancellation
You can contact us through:
- Email: support@ibspot.com
- Contact Form: Submit a request through our Contact Us page
Please submit your cancellation request as soon as possible after placing the order to allow us to process it before shipment.
Return Policy
We accept returns for most items within 30 days of delivery for a full refund.
To be eligible for a return:
- The item must be unused, in the same condition as received, and in its original packaging.
- A tracking number must be provided to confirm the return shipment.
Non-Returnable Items
Certain products cannot be returned, including:
- Perishable goods (for example, food, flowers, newspapers, magazines)
- Intimate or sanitary goods
- Hazardous materials or flammable liquids/gases
- Gift cards
- Downloadable software
- Some health and personal care items
Partial Refunds (If Applicable)
Partial refunds may be granted in specific situations, such as:
- Books with obvious signs of use
- Opened CDs, DVDs, software, or vinyl records
- Items not in their original condition, damaged, or missing parts not due to our error
- Items returned more than 30 days after delivery
How to Return an Item
To initiate a return, please contact us at support@ibspot.com with your order number and details about the product you wish to return.
Our team will provide you with return instructions and a prepaid return label.
Shipping Cost for Returns
Please contact us before returning any item.
We will provide a free return shipping label.
If a return is sent back without prior contact or without our provided label, we cannot be held responsible for return shipping costs.
For items valued over $75, we recommend using a trackable shipping service or purchasing shipping insurance.
We cannot guarantee that we will receive your returned item if shipped independently.
Refund Processing
Once your return is received and inspected:
- In-store returns are refunded to the original form of payment or issued as a gift card.
- Mail-in returns using our prepaid label are refunded to the original payment method within 3–5 business days after we receive your return.
Please allow:
- 5–7 business days for the return to reach our Returns Center.
- An additional 3–10 business days for your bank to post the refund to your account.
Damages, Issues & Claims
Please inspect your order immediately upon receipt.
If you receive a defective, damaged, or incorrect item, contact us right away at support@ibspot.com.
We’ll evaluate the issue promptly and make it right.
Product Claims
Before purchasing, please review product details carefully.
If there is a problem with your order upon arrival, visit our Support Center or contact us directly to arrange return shipping or replacement.
Exchanges
We do not process direct exchanges.
The fastest way to get what you need is to return the original item and place a new order once your return is accepted.
Return Address
IBSPOT Return Center
15 Sawmill Ln
Dover Plains, NY 12522
United States
Customer Support
Our support team is available 24/7 to assist with cancellations, returns, or general inquiries.
Email: support@ibspot.com
Contact Form: Contact Us page
Oops!
Sorry, it looks like some products are not available in selected quantity.