autoutdoor For 2002-03 Oldsmobile Bravada 14x Front Wheel Bearning Hub Sway Bar Ball Joint
autoutdoor For 2002-03 Oldsmobile Bravada 14x Front Wheel Bearning Hub Sway Bar Ball Joint
2x Front Upper Ball Joint -K6664
2x Front Lower Ball Joint -K6663
1x Rear Sway Bar End Link - Passenger Side -K6667
1x Rear Sway Bar End Link - Driver Side -K6668
1x Front Outer Tie Rod End - Driver Side -ES3675
1x Front Outer Tie Rod End - Passenger Side -ES3676
2x Front Inner Tie Rod End -EV80965
1x Front Sway Bar End Link - Passenger Side -K6665
1x Front Sway Bar End Link - Driver Side -K6666
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1.Fitting the Following vehicle:
2002-2003 Chevrolet Trailblazer2002-2003 Chevrolet Trailblazer EXT
2002-2003 GMC Envoy
2002-2003 GMC Envoy XL
2003 Isuzu Ascender
2002-2003 Oldsmobile Bravada
2.Package Includes:
2x Front Wheel Hub Bearing -5131882x Front Upper Ball Joint -K6664
2x Front Lower Ball Joint -K6663
1x Rear Sway Bar End Link - Passenger Side -K6667
1x Rear Sway Bar End Link - Driver Side -K6668
1x Front Outer Tie Rod End - Driver Side -ES3675
1x Front Outer Tie Rod End - Passenger Side -ES3676
2x Front Inner Tie Rod End -EV80965
1x Front Sway Bar End Link - Passenger Side -K6665
1x Front Sway Bar End Link - Driver Side -K6666
Tie-Rod End Replacement Guideline:
If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely.
This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod.
Picture(A)
Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance.
1.Lift the vehicle and dismount the front axle wheels.
2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes.
Picture(B)
3.Dismount the front underride guard.
Picture(C)
4.Loosen the fastening nut from the tie rod and remove it completely.
5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator.
Picture(D)
6.Remove the clamp of the bellow on the steering gear.
7.Push the bellow towards the tie rod end.
Picture(E)
8.Unscrew the inner tie rod from the rack.
9.Clean the sealing face of the bellow at the steering gear.
Picture(F)
10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle.
Note:Always use new self-locking nuts and bolts for a reliable repair.
11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer.
Picture(G)
12.Mount the bellow and close the clamps with the appropriate special tool.
Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance.
Picture(H)
13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer.
Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure.
Tip:Secure the ball stud against twisting with a suitable tool.
Picture(I)
14.Mount the front underride guard.
15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer.
16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications.
17.Perform a test drive.
Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission.
Ball Joint Replacement Guideline:
If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension.
Picture(A)
The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty.
Picture(B)
1.Raise the vehicle and remove the front wheels.
2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes.
Picture(C)
3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts.
Picture(D)
4.Loosen and remove the fixing nut of the ball joint on the steering knuckle.
Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket.
Picture(E)
5.Remove the bad or worn ball joint from the control arm.
6.Loosen the compression ball joint on the steering knuckle using a suitable special tool.
Picture(F)
7.Clean the cone connection.
Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface.
Picture(G)
8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts.
9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer.
10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary.
11.Finally, carry out a test drive.
Sway Bar Stabilizer Link Replacement Guideline:
While driving, the following signs may indicate a faulty sway bar stabilizer link:
(1).Rattling and thumping noises on rough roads.
(2).Imprecise vehicle handling.
(3).Stronger inclination of the vehicle during cornering.
If the sway bar stabilizer link is found to be defective, it should be replaced as described below.
Picture(A)
1.Raise vehicle and remove front wheels.
Tip:Always check both stabilizer links and replace them in pairs if necessary.
2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes.
Picture(B)
3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove.
Tip:If the ball stud also starts to turn, hold it with a suitable tool.
4.Press stabilizer link out of torsion bar.
Picture(C)
5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it.
Tip:If the ball stud also starts to turn, hold it with a suitable tool.
Picture(D)
6.Press stabilizer link at suspension strut out of bracket.
Picture(E)
7.Insert new stabilizer link at suspension strut.
Picture(F)
8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer.
Tip:Secure the ball stud against twisting with a suitable tool.
Picture(G)
9.Insert new stabilizer link at stabilizer.
10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer.
Tip:Secure the ball stud against twisting with a suitable tool.
Picture(H)
11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer.
Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension.
12.Conclude with a test drive.
Item Specifics | |
---|---|
Brand : | autoutdoor |
Type : | Sway Bar Link |
Universal Fitment : | No |
Included Hardware : | Mounting Hardware |
Performance Part : | No |
Interchange Part Number : | 513188,K6664,K6663,K6667,K6668,ES3675,ES3676,EV80965,K6665,K6666 |
Superseded Part Number : | stabilizer bar linkage,wheel hub bearing assembly,hubs bearings |
OE/OEM Part Number : | rods ends,car tie rod end replacement,anti sway bar,anti roll bar |
Finish : | Coated |
Manufacturer Warranty : | 10 Year |
Placement on Vehicle : | Front Upper Lower Rear Right Left Outer Inner |
Manufacturer Part Number : | ADD84104702R |
Adjustable : | Yes |
Material : | Alloy Steel |
Kit or Single Part : | Kit |
Greasable or Sealed : | Greasable |
OE Spec or Performance/Custom : | OE Spec |
Surface Finish : | Polished, Rust Protected |
Quantity : | 14Pcs |
Items Included : | Mounting Hardware |
ABS Sensor : | Has ABS with tegral Sensor |
Bolt Circle Diameter : | 16.666665cm |
We will only ship to the confirmed shipping address given with the payment.
We do not offer local pickups.
1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
2. The images shown are not the actual item and are for your reference only.
3. Fast shipping:All our packages use USPS Package Service
4. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
1. You have 7 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
4. Return shipping is to be paid by the Buyer.
We are always been trying to provide best service and reliable products for every customer.
If you are satisfed with the product you recieved,please leave us positive feedback.
If you are not satisfied for any reason, please do not be quick to leave negative or neutral feedback.We will work hard to make sure every customer 100 percent satisfied, and reslove any problem for you.
Shop Category |
For 2002-03 Oldsmobile Bravada 14x Front Wheel Bearning Hub Sway Bar Ball Joint
1.Fitting the Following vehicle: 2002-2003 Chevrolet Trailblazer2002-2003 Chevrolet Trailblazer EXT 2002-2003 GMC Envoy 2002-2003 GMC Envoy XL 2003 Isuzu Ascender 2002-2003 Oldsmobile Bravada
2.Package Includes: 2x Front Wheel Hub Bearing -5131882x Front Upper Ball Joint -K6664 2x Front Lower Ball Joint -K6663 1x Rear Sway Bar End Link - Passenger Side -K6667 1x Rear Sway Bar End Link - Driver Side -K6668 1x Front Outer Tie Rod End - Driver Side -ES3675 1x Front Outer Tie Rod End - Passenger Side -ES3676 2x Front Inner Tie Rod End -EV80965 1x Front Sway Bar End Link - Passenger Side -K6665 1x Front Sway Bar End Link - Driver Side -K6666
Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. Picture(A)
Picture(B)
Picture(C)
Picture(D)
Picture(E)
Picture(F)
Picture(G)
Picture(H)
Picture(I) 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications.
Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty.
Picture(B)
Picture(C)
Picture(D)
Picture(E)
Picture(F)
Picture(G)
Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link:
1.Raise vehicle and remove front wheels.
Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove.
Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it.
Picture(D) 6.Press stabilizer link at suspension strut out of bracket.
Picture(E) 7.Insert new stabilizer link at suspension strut.
Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer.
Picture(G) 9.Insert new stabilizer link at stabilizer.
Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer.
We will only ship to the confirmed shipping address given with the payment. We do not offer local pickups. 1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 2. The images shown are not the actual item and are for your reference only. 3. Fast shipping:All our packages use USPS Package Service 4. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction! 1. You have 7 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! 2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable. 3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. 4. Return shipping is to be paid by the Buyer. We are always been trying to provide best service and reliable products for every customer.
Copyright of autoutdoor. All rights reserved. |
Brand: | autoutdoor |
---|---|
Isin: | IQRELRXPLANU |

IBspot Buyer Protection
Shop confidently on IBspot, receive your item as described or your money back for eligible orders. Learn Program Terms

GUARANTEED SAFE CHECKOUT
-
MONEY BACK GUARANTEE
30 days money back guarantee, no additional fee charged.
-
EXCELLENT SUPPORT
We provide 24/7 online customer support via email.
-
Fast Shipping
One week domestic shipping. Global delivery to the US in 2 weeks.
2x Front Upper Ball Joint -K6664
2x Front Lower Ball Joint -K6663
1x Rear Sway Bar End Link - Passenger Side -K6667
1x Rear Sway Bar End Link - Driver Side -K6668
1x Front Outer Tie Rod End - Driver Side -ES3675
1x Front Outer Tie Rod End - Passenger Side -ES3676
2x Front Inner Tie Rod End -EV80965
1x Front Sway Bar End Link - Passenger Side -K6665
1x Front Sway Bar End Link - Driver Side -K6666

|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1.Fitting the Following vehicle:
2002-2003 Chevrolet Trailblazer2002-2003 Chevrolet Trailblazer EXT
2002-2003 GMC Envoy
2002-2003 GMC Envoy XL
2003 Isuzu Ascender
2002-2003 Oldsmobile Bravada
2.Package Includes:
2x Front Wheel Hub Bearing -5131882x Front Upper Ball Joint -K6664
2x Front Lower Ball Joint -K6663
1x Rear Sway Bar End Link - Passenger Side -K6667
1x Rear Sway Bar End Link - Driver Side -K6668
1x Front Outer Tie Rod End - Driver Side -ES3675
1x Front Outer Tie Rod End - Passenger Side -ES3676
2x Front Inner Tie Rod End -EV80965
1x Front Sway Bar End Link - Passenger Side -K6665
1x Front Sway Bar End Link - Driver Side -K6666
Tie-Rod End Replacement Guideline:
If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely.
This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod.
Picture(A)
Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance.
1.Lift the vehicle and dismount the front axle wheels.
2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes.
Picture(B)
3.Dismount the front underride guard.
Picture(C)
4.Loosen the fastening nut from the tie rod and remove it completely.
5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator.
Picture(D)
6.Remove the clamp of the bellow on the steering gear.
7.Push the bellow towards the tie rod end.
Picture(E)
8.Unscrew the inner tie rod from the rack.
9.Clean the sealing face of the bellow at the steering gear.
Picture(F)
10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle.
Note:Always use new self-locking nuts and bolts for a reliable repair.
11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer.
Picture(G)
12.Mount the bellow and close the clamps with the appropriate special tool.
Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance.
Picture(H)
13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer.
Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure.
Tip:Secure the ball stud against twisting with a suitable tool.
Picture(I)
14.Mount the front underride guard.
15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer.
16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications.
17.Perform a test drive.
Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission.
Ball Joint Replacement Guideline:
If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension.
Picture(A)
The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty.
Picture(B)
1.Raise the vehicle and remove the front wheels.
2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes.
Picture(C)
3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts.
Picture(D)
4.Loosen and remove the fixing nut of the ball joint on the steering knuckle.
Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket.
Picture(E)
5.Remove the bad or worn ball joint from the control arm.
6.Loosen the compression ball joint on the steering knuckle using a suitable special tool.
Picture(F)
7.Clean the cone connection.
Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface.
Picture(G)
8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts.
9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer.
10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary.
11.Finally, carry out a test drive.
Sway Bar Stabilizer Link Replacement Guideline:
While driving, the following signs may indicate a faulty sway bar stabilizer link:
(1).Rattling and thumping noises on rough roads.
(2).Imprecise vehicle handling.
(3).Stronger inclination of the vehicle during cornering.
If the sway bar stabilizer link is found to be defective, it should be replaced as described below.
Picture(A)
1.Raise vehicle and remove front wheels.
Tip:Always check both stabilizer links and replace them in pairs if necessary.
2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes.
Picture(B)
3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove.
Tip:If the ball stud also starts to turn, hold it with a suitable tool.
4.Press stabilizer link out of torsion bar.
Picture(C)
5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it.
Tip:If the ball stud also starts to turn, hold it with a suitable tool.
Picture(D)
6.Press stabilizer link at suspension strut out of bracket.
Picture(E)
7.Insert new stabilizer link at suspension strut.
Picture(F)
8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer.
Tip:Secure the ball stud against twisting with a suitable tool.
Picture(G)
9.Insert new stabilizer link at stabilizer.
10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer.
Tip:Secure the ball stud against twisting with a suitable tool.
Picture(H)
11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer.
Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension.
12.Conclude with a test drive.
Item Specifics | |
---|---|
Brand : | autoutdoor |
Type : | Sway Bar Link |
Universal Fitment : | No |
Included Hardware : | Mounting Hardware |
Performance Part : | No |
Interchange Part Number : | 513188,K6664,K6663,K6667,K6668,ES3675,ES3676,EV80965,K6665,K6666 |
Superseded Part Number : | stabilizer bar linkage,wheel hub bearing assembly,hubs bearings |
OE/OEM Part Number : | rods ends,car tie rod end replacement,anti sway bar,anti roll bar |
Finish : | Coated |
Manufacturer Warranty : | 10 Year |
Placement on Vehicle : | Front Upper Lower Rear Right Left Outer Inner |
Manufacturer Part Number : | ADD84104702R |
Adjustable : | Yes |
Material : | Alloy Steel |
Kit or Single Part : | Kit |
Greasable or Sealed : | Greasable |
OE Spec or Performance/Custom : | OE Spec |
Surface Finish : | Polished, Rust Protected |
Quantity : | 14Pcs |
Items Included : | Mounting Hardware |
ABS Sensor : | Has ABS with tegral Sensor |
Bolt Circle Diameter : | 16.666665cm |
We will only ship to the confirmed shipping address given with the payment.
We do not offer local pickups.
1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
2. The images shown are not the actual item and are for your reference only.
3. Fast shipping:All our packages use USPS Package Service
4. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
1. You have 7 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
4. Return shipping is to be paid by the Buyer.
We are always been trying to provide best service and reliable products for every customer.
If you are satisfed with the product you recieved,please leave us positive feedback.
If you are not satisfied for any reason, please do not be quick to leave negative or neutral feedback.We will work hard to make sure every customer 100 percent satisfied, and reslove any problem for you.
Shop Category |
For 2002-03 Oldsmobile Bravada 14x Front Wheel Bearning Hub Sway Bar Ball Joint
1.Fitting the Following vehicle: 2002-2003 Chevrolet Trailblazer2002-2003 Chevrolet Trailblazer EXT 2002-2003 GMC Envoy 2002-2003 GMC Envoy XL 2003 Isuzu Ascender 2002-2003 Oldsmobile Bravada
2.Package Includes: 2x Front Wheel Hub Bearing -5131882x Front Upper Ball Joint -K6664 2x Front Lower Ball Joint -K6663 1x Rear Sway Bar End Link - Passenger Side -K6667 1x Rear Sway Bar End Link - Driver Side -K6668 1x Front Outer Tie Rod End - Driver Side -ES3675 1x Front Outer Tie Rod End - Passenger Side -ES3676 2x Front Inner Tie Rod End -EV80965 1x Front Sway Bar End Link - Passenger Side -K6665 1x Front Sway Bar End Link - Driver Side -K6666
Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. Picture(A)
Picture(B)
Picture(C)
Picture(D)
Picture(E)
Picture(F)
Picture(G)
Picture(H)
Picture(I) 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications.
Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty.
Picture(B)
Picture(C)
Picture(D)
Picture(E)
Picture(F)
Picture(G)
Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link:
1.Raise vehicle and remove front wheels.
Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove.
Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it.
Picture(D) 6.Press stabilizer link at suspension strut out of bracket.
Picture(E) 7.Insert new stabilizer link at suspension strut.
Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer.
Picture(G) 9.Insert new stabilizer link at stabilizer.
Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer.
We will only ship to the confirmed shipping address given with the payment. We do not offer local pickups. 1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 2. The images shown are not the actual item and are for your reference only. 3. Fast shipping:All our packages use USPS Package Service 4. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction! 1. You have 7 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! 2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable. 3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. 4. Return shipping is to be paid by the Buyer. We are always been trying to provide best service and reliable products for every customer.
Copyright of autoutdoor. All rights reserved. |

- Brand: autoutdoor
- Type: Sway Bar Link
- Universal Fitment: No
- Included Hardware: Mounting Hardware
- Performance Part: No
- Interchange Part Number: 513188,K6664,K6663,K6667,K6668,ES3675,ES3676,EV80965,K6665,K6666
- Superseded Part Number: stabilizer bar linkage,wheel hub bearing assembly,hubs bearings
- OE/OEM Part Number: rods ends,car tie rod end replacement,anti sway bar,anti roll bar
- Finish: Coated
- Manufacturer Warranty: 10 Year
- Placement on Vehicle: Front, Upper, Lower, Rear, Right, Left, Outer, Inner
- UPC: Does not apply
- Manufacturer Part Number: ADD84104702R
- Adjustable: Yes
- Material: Alloy Steel
- Kit or Single Part: Kit
- Features: Greasable
- OE Spec or Performance/Custom: OE Spec
- Surface Finish: Polished, Rust Protected
- Quantity: 14Pcs
- Items Included: Mounting Hardware
- ABS Sensor: Has ABS with tegral Sensor
- Bolt Circle Diameter: 16.666665cm
Shipping Summary:
- Packages are shipped from Monday to Friday.
- The usual time for processing an order is 1 to 3 business days, but may vary depending on the availability of products ordered. This period excludes delivery times, which depend on your geographic location.
- We provide tracking for every order. Tracking will be available once your product is shipped. Each individual product may be shipped from different fulfillment centers across the globe as our product research team spends the time to source quality yet affordable products.
Estimated delivery times:
- Standard Shipping: 3-7 business days
- Expedited Shipping: 2-5 business days
- International Shipping: 10 - 15 business days
Please note that these are estimates, not guarantees. Delivery time depends on a number of variables, and there may be delays such as bad weather affecting air transport, or a package being held for inspection by Customs. ibspot is not liable for any delays in international transportation or customs clearance.
Shipments can be delivered directly to most addresses, except post office boxes. However, in certain remote areas, there may be an additional delivery charge or you may need to pick up your package from the closest service location of ibspot's shipping partner.
Shipping Status:
As soon as your order ships, you'll receive a shipping confirmation email that includes your tracking number.
If you don't receive a shipping confirmation email right away, don't worry! We know the delivery date or date range provided at checkout and we'll be sure to deliver the items within that timeframe.
Order changes:
Please contact our customer support if the order needs to be canceled or modified.
Item not received:
If you've successfully placed an order and haven't received it yet while the tracking status shows it's delivered. you'd wish to contact the carrier to hunt the packages. Once a package is marked “Delivered” by the carrier, we are no longer responsible for lost or stolen items. Please ensure you provide a secure delivery address.
Damaged Parcel
If your package has been delivered in a PO Box, please note that we are not responsible for any damage that may result (consequences of extreme temperatures, theft, etc.).
If you have any questions regarding shipping or want to know about the status of an order, please contact us or email to support@ibspot.com.
Please Read Our Return & Refund Policy Carefully:
Return:
You may return most items within 30 days of delivery for a full refund.
To be eligible for a return, your item must be unused and in the same condition that you received it. It must also be in the original packaging.
Several types of goods are exempt from being returned. Perishable goods such as food, flowers, newspapers or magazines cannot be returned. We also do not accept products that are intimate or sanitary goods, hazardous materials, or flammable liquids or gases.
Additional non-returnable items:
- Gift cards
- Downloadable software products
- Some health and personal care items
To complete your return, we require a tracking number, which shows the items which you already returned to us.
There are certain situations where only partial refunds are granted (if applicable)
- Book with obvious signs of use
- CD, DVD, VHS tape, software, video game, cassette tape, or vinyl record that has been opened
- Any item not in its original condition, is damaged or missing parts for reasons not due to our error
- Any item that is returned more than 30 days after delivery
Items returned to us as a result of our error will receive a full refund,some returns may be subject to a restocking fee of 7% of the total item price, please contact a customer care team member to see if your return is subject. Returns that arrived on time and were as described are subject to a restocking fee.
Items returned to us that were not the result of our error, including items returned to us due to an invalid or incomplete address, will be refunded the original item price less our standard restocking fees.
You should expect to receive your refund within four weeks of giving your package to the return shipper, however, in many cases you will receive a refund more quickly. This time period includes the transit time for us to receive your return from the shipper (5 to 10 business days), the time it takes us to process your return once we receive it (3 to 5 business days), and the time it takes your bank to process our refund request (5 to 10 business days).
If you need to return an item, please Contact Us with your order number and details about the product you would like to return. We will respond quickly with instructions for how to return items from your order.
Shipping Cost
We'll pay the return shipping costs if the return is a result of our error (you received an incorrect or defective item, etc.). In other cases, you will be responsible for paying for your own shipping costs for returning your item. Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund.
Depending on where you live, the time it may take for your exchanged product to reach you, may vary.
If you are shipping an item over $75, you should consider using a trackable shipping service or purchasing shipping insurance. We don’t guarantee that we will receive your returned item.
Refund:
- Purchases may be returned within 30 days of the shipping date for a refund.
- Refund will be issued to your original form of payment.
- Refunds for orders purchased with IBSPOT Gift Cards and/or IBSPOT Notes will be issued as a IBSPOT Gift Card and mailed to the original billing address. Gift cards cannot be redeemed for cash unless required by law.
Refund Processing
• Returns to a IBSPOT store will be refunded to the original form of payment or gift card. • Mail-in returns with our prepaid return label will be refunded back to the original form of payment within 3-5 business days after we receive your return. Please allow 5-7 business days for your return to arrive at our Returns Center.
• Note: It may take a few days until your bank posts the refund to your account.
Claims:
Claims related to the product. Be sure to check the details of your purchase carefully before you make the payment, and check the contents of the package(s) promptly upon receipt. If you have a problem with the product, visit our Support Center to find out about return shipping arrangements.
WHICH CIRCUMSTANCES WE OFFER RETURND & REFUND:
WRONG PRODUCT:
If you discover your order is flawed please contact us Mail: support@ibspot.com. With photos of the wrong product we will providing a return shipping label. Once it is tracking we will ship a replacement a product immediately.
Damages and issues
Please inspect your order upon reception and contact us immediately if the item is defective, damaged or if you receive the wrong item, so that we can evaluate the issue and make it right.
Exceptions / non-returnable items
Certain types of items cannot be returned, like perishable goods (such as food, flowers, or plants), custom products (such as special orders or personalized items), and personal care goods (such as beauty products). We also do not accept returns for hazardous materials, flammable liquids, or gases. Please get in touch if you have questions or concerns about your specific item. Unfortunately, we cannot accept returns on sale items or gift cards.
Exchanges
The fastest way to ensure you get what you want is to return the item you have, and once the return is accepted, make a separate purchase for the new item.
Oops!
Sorry, it looks like some products are not available in selected quantity.